Overview
This 28.8 kWp hybrid rooftop system was designed for a private villa in Mauritania. Forty-eight Jinko 600 W modules feed a Deye 29.9 kW three-phase hybrid inverter backed by battery storage, keeping the villa powered by solar first, with the grid and the battery as support. The work covered manual sizing and energy calculations, a PVsyst simulation of an earlier design iteration, the single-line diagram, the general layout, the shop drawing and the full bill of quantities.
Scope of work
- Manual system sizing and energy calculations
- PVsyst energy simulation
- Single-line diagram (SLD)
- General layout and arrangement
- Shop drawing for execution
- Bill of quantities and cable protection sizing
System layout
Key design data
| Item | Detail | Value |
|---|---|---|
| PV array | 48 × Jinko JKM600N-66HL4M, 600 W mono PERC | 28.8 kWp |
| Stringing | 3 strings × 16 modules in series | 3 MPPT |
| Inverter | Deye SUN-29.9K-SG01HP3, hybrid, three-phase | 29.9 kW AC |
| MPPT window | 150–850 V operating, 1000 V max input, 55 A max | — |
| Storage | Deye Li-ion battery, 51.2 V / 100 Ah | ≈5.1 kWh |
| Array tilt | 22° on a steel / galvanised sheet roof | 22° |
String sizing was verified against the inverter limits at temperature extremes: the open-circuit voltage of one string at −5 °C stays well below the 1000 V maximum, and the operating voltage at 70 °C stays inside the MPPT window.
| DC check | Result | Limit |
|---|---|---|
| Voc per string at −5 °C | 825.0 V | < 1000 V max ✓ |
| Vmpp per string at 70 °C | 577.4 V | 150–850 V MPPT ✓ |
Design drawings
Design drawings — the single-line diagram, the general roof layout and the execution shop drawing. Tap any drawing to open the viewer, then swipe or use the arrows to move between them.
Bill of quantities
Bill of quantities — the equipment and material list behind the drawings, as prepared in the project workbook. The original Excel sheet is shown below the table.
| Item | Description | Qty |
|---|---|---|
| PV modules | Jinko JKM600N-66HL4M, 600 W mono PERC | 48 |
| Hybrid inverter | Deye SUN-29.9K-SG01HP3, 29.9 kW AC, 3 MPPT | 1 |
| Battery | Deye Li-ion, 51.2 V / 100 Ah | 1 |
| Solar DC cable | PV1-F 1×6 mm², UV-resistant | Lot |
| String fuses | 20 A gPV, in fuse holders | 4 |
| DC isolator | 1000 V / 32 A, pole-mounted near inverter | 1 |
| DC surge protection | Type II SPD, DC side | 1 |
| AC breaker | MCCB 40 A / 4P | 1 |
| AC cable | 3×16 mm² copper | Lot |
| Junction boxes | IP65, outdoor rated | 2 |
| Earthing | Earth rods with bonding to structure | 2 |
| Mounting | Steel / GAL rails at 22° tilt on sheet roof | Lot |
Energy simulation (PVsyst)
PVsyst simulation report — the energy study behind the design. The published report is the earlier grid-connected design iteration (variant VC0): 32 modules of the same Jinko 600 W type in 2 strings (19.2 kWp) feeding a Huawei 18 kW AC inverter at a 22° tilt. It simulated about 32,911 kWh/year with a performance ratio of 85.6%. The final executed design evolved from this study into the 48-module hybrid system shown above. Client name and exact site coordinates are redacted; only general site data is shown.
Deliverables
- Sizing and energy calculations workbook
- PVsyst simulation report
- Single-line diagram
- General layout drawing
- Shop drawing for execution
- Bill of quantities